How to perform a Dumas method for nitrogen determination in fertilisers

Fertiliser labels often promise nitrogen contents such as 46% for urea or 21% for ammonium sulphate. Those percentages guide purchasing, crop calculations and quality checks, so reliable total nitrogen analysis matters whenever a laboratory verifies a product or investigates a disputed batch.

Dumas analysis measures nitrogen by burning a small sample in a controlled gas stream. The instrument converts nitrogen into a measurable gas, removes carbon dioxide and water, and detects nitrogen with a thermal conductivity detector. The result is calculated from the sample mass and the detector response.

This guide covers solid fertilisers, including urea, ammonium sulphate, ammonium nitrate and NPK blends. It also explains the sample preparation, calibration and quality checks needed to turn the instrument reading into a defensible nitrogen percentage.

What Dumas analysis measures

Nitrogen in fertiliser can occur as nitrate, ammonium, urea or in other organic and inorganic forms. A properly validated Dumas method determines total nitrogen after suitable conversion, rather than only the immediately available nitrogen.

Combustion temperatures are commonly around 800–1000 °C. Sample nitrogen passes through ammonia and nitrogen-oxide intermediates before a reduction stage produces molecular nitrogen. Instrument settings must be validated for the fertiliser matrix, especially nitrate-rich products, because an unsuitable programme can cause incomplete conversion or low recovery.

Equipment and reagents

Use an elemental analyser configured for Dumas measurements, with a combustion furnace, temperature control, gas-flow regulation, carbon-dioxide and water removal stages, and a thermal conductivity detector. Certified reference materials, ceramic sample boats, a precision balance and high-purity oxygen are also required. Follow the manufacturer’s validated method rather than combining settings from different instruments.

Plan for reagent blanks, duplicate portions and a certified nitrogen reference material with a known value and uncertainty. Wear the eye, hand and respiratory protection specified by the safety data sheets, restrain gas cylinders, and allow the furnace and exhaust system to cool before handling spent material.

Preparing and running the sample

Label the sample and record its batch, source and intended reporting basis. Crush granules, mix thoroughly and grind a representative subsample to a consistent particle size. Determine moisture on a separate portion using a validated method; do not assume that air-dried material is dry. State clearly whether the result is as received or corrected to a dry basis.

Weigh approximately 50–150 mg into a clean combustion boat, adjusting within the instrument’s validated range. Run a reagent blank and the certified reference material alongside the samples. Seal the remaining powder in a moisture-tight container to prevent changes before the duplicate analysis.

Load the boat and start the validated combustion cycle. Keep oxygen flow and detector temperature stable, then wait for the nitrogen peak to return to baseline. Save the peak area, sample mass and calculated result for every run, and inspect the trace for incomplete combustion, carry-over or an unusual baseline.

Method Typical nitrogen coverage Useful feature Main limitation
Dumas elemental analysis Total nitrogen after validated conversion Fast, automated analysis with permanent-gas detection Requires instrument-specific validation and suitable conversion conditions
Kjeldahl digestion and distillation Ammonium and organic nitrogen in suitable matrices Established wet chemistry with familiar calculations Standard digestion does not recover nitrate or nitrite nitrogen
Devarda alloy digestion and distillation Ammonium and nitrate nitrogen Useful for checking mixed nitrogen fertilisers Slower, produces hydrogen, and does not universally recover all organic nitrogen

Calculating and validating the result

If the analyser reports nitrogen mass, calculate the mass percentage as N (%) = (mass of nitrogen ÷ test-portion mass) × 100. Keep the units consistent. Check whether the instrument reports nitrogen, ammonia or another nitrogen-equivalent value, and apply only the conversion documented in its method.

Control charts should include blank response, reference-material recovery and duplicate agreement. Set acceptance limits during method validation; a duplicate relative standard deviation below 2% is often practical for a homogeneous fertiliser, but the laboratory’s validated criteria take precedence. A reference material outside its recovery limits invalidates associated sample results until the cause is resolved.

Low results can reflect poor grinding, moisture variation, sample loss or incomplete conversion. High results may come from contamination, carry-over or an incorrect blank. Repeat the check material after correcting the fault, and examine the combustion trace before accepting the original result.

Fitting the work into Australian practice

Australian distributors handle imported urea and blended fertilisers through supply chains centred on Sydney and Melbourne. Brisbane serves many farms in Queensland and northern New South Wales. Because growers compare cost per kilogram of nitrogen, verified percentages support both purchasing decisions and fertiliser blending.

Customs and biosecurity remain separate from laboratory analysis. Importers should check current commodity requirements in BICON and with the Department of Agriculture, Fisheries and Forestry; a certificate of analysis does not replace border documentation. Nitrogen claims sold in Australia must also comply with applicable Australian Competition and Consumer Commission requirements and state and territory product-quality rules.

Seek traceable calibration and reference materials through the National Measurement Institute or another technically competent provider, and consider a NATA-accredited laboratory when a result needs contractual acceptance. Store ground samples in sealed containers: coastal humidity and hot inland conditions can change moisture and therefore the as-received nitrogen value. Record the reporting basis beside every result.

The immediate next step is to analyse a 0.10 g portion of the prepared, homogenised sample alongside a certified nitrogen reference material, then file its chromatogram, calibration record and calculated nitrogen percentage with the batch identification.